How To Check And Clear The Hayward Aqua Rite Cell?

This video demonstrates how to remove the “inspect cell” light on all Hayward AquaRite salt chlorination systems. To manually reset the Inspect Cell LED, press and hold the Diagnostics button until the LED goes out (approximately 3 to 5 seconds). If both the “check salt” and “inspect cell” lights stay on, it most likely means that no chlorine is being produced at this time and your salt level fell below 2300 ppm. If the pool has the proper amount of salt and the “Inspect Cell” LED is on, you can manually reset the Inspect Cell LED by pressing and holding the diagnostic button for 3 to 5 seconds.

The Hayward AquaRite salt chlorination system has a built-in reminder to inspect and clean the cell every 500 hours. To reset the Inspect Cell LED, press the menu until the “Default Menu” appears on the display. Press the (>) key repeatedly until “Inspect Cell, Hold”. If the Inspect Cell Light is the only LED light flashing, you can reset it by holding down the diagnostic button for 3 seconds and then release.

For AquaRite, move the switch from auto to off and check all of the readings. Move the switch back to auto and recheck the readings. Use a 50 water, 50 muriatic acid solution and let it sit for 20 minutes or use a hose and spray it. If your independent testing shows your salt levels are correct, you may need to recalibrate your Aqua Rite unit. Pushing the diagnostics button three times will clear the flashing “inspect” light.

How to reset inspect cell?

The internal clock has been reset, and the accumulated running hours will be recalculated from zero and continue to be updated until the conclusion of the voting period.

How do you recalibrate Hayward aquarite salt cell?

To calibrate your Hayward AquaRite, first ensure your salt cell is clean to avoid false salinity readings. Then, switch the main switch from “Auto” to “Off” and then back to “Auto” while the pump is running. Wait for the relay click, which takes 5-10 seconds. Press the diagnostics button five times to display instant salinity, which will begin the calibration process. The number on the display will start high and begin to decrease. Once the number matches the actual salt level in your pool, slide the switch up to “Super Chlorinate” and back down to “Auto”.

To reset the average salt level, follow these steps:

1. Turn the switch to “Off” and then back to “Auto” for 5-10 seconds. Press the diagnostics button five times to display the instant salt level and wait for the number to stabilize.
2. Slide the switch up to “Super Chlorinate” and back to “Auto” for 30 seconds.
3. Reset the unit to the default reading and repeat this process to ensure both polarities, side A and side B, read within 500 ppm of each other.

How do I reset my salt Hayward Aquarite?

To reset the average salt level in the Hayward AquaRite salt system, turn the switch to “Off” and then back to “Auto” for 5-10 seconds. Press the diagnostics button 5 times to display the instant salt level and wait for it to stabilize. The AquaRite salt system is the world’s number one selling salt system, efficiently sanitizing pool water by transforming sodium chloride into free chlorine. Once bacteria and algae are eliminated, chlorine reverts back into salt.

The AquaRite controller is user-friendly and allows easy management of chlorine output. To recalibrate and troubleshoot the system, press the diagnostic button on the AquaRite control panel, which displays information such as pool temperature, cell voltage, current, desired output, instant salinity, product name, software revision level, and chlorinator cell type.

How do you reset the inspect cell light on a Hayward AquaRite pool?

The AquaRite Salt Chlorination Inspect Cell Light can be reset by holding down the diagnostic button for 3 seconds and releasing. The indicator will reset after 500 hours of use. To determine the amount of salt in your pool, use the Hayward Water Chemistry Calculator. Hayward has introduced the Extended Life TurboCell, a new option in the Genuine Hayward TurboCell Family. This new TurboCell provides silky water without irritants or dryness, and eliminates harsh chlorine odors. Salt Chlorination provides a continuous supply of fresh, natural chlorine, allowing for significant cost savings over time. The new Salt Cell offers a healthier and more luxurious pool experience.

How do I reset my Hayward pool light?

To restore the ColorLogic settings to their original defaults, navigate to the “Config.” menu item and press the Menu button until the desired option is highlighted. Once the “Menu – Locked” prompt appears, proceed to unlock it. Then, using the arrow key, navigate to and select “Reset ColorLogic to Default.”

How often should you clean a Hayward salt cell?

It is recommended that the salt chlorinator cell be inspected and cleaned every three months.

How long does an aqua rite cell last?

Salt water pools provide a gentler, less expensive alternative to chlorine pools, with swimmers experiencing less side effects and less frequent maintenance costs. The salt chlorine generator cell in your pool can last about five years with proper care. However, it’s important to check for signs that could cause a cell to shut down or stop performing as it should.

To maintain the cell’s longevity, keep pool chemicals balanced, as prolonged exposure to outside optimum ranges can damage the cell’s plates. Additionally, if the stabilizer runs too low, the pool won’t hold the chlorine generated by the generator, making it appear bad when it’s not.

Check the “Inspect Cell” light every 500 hours to ensure the cell is functioning properly. Increase the output if necessary, especially if the pool temperature is warm or if many people are swimming. Check the salt level to determine the optimal level for your SCG, which can be found in your owner’s manual or tested using salt strips.

If the flow level is illuminated, it may indicate a bad flow switch or system restriction. Corroded or disconnected plates are also signs of a cell needing replacement. If the cell still doesn’t generate enough chlorine after cleaning, it’s time to replace it. If the cell isn’t cleaned often enough, it may need to be replaced.

How do you clean the cells on Aqua Rite?

The manufacturer recommends checking the Hayward AquaRite Turbo Cell 3-4 times a year for hard mineral deposits to build up on its electrolytic plates. After cleaning the cell with a 50 Water to Muriatic Acid Solution, the cell showed red flashing NO FLOW after a recent storm. After clearing out debris and replacing the cell, the red flashing light remains and the cell is clean. The chemicals in the pool show they are balanced and within the normal/OK range. Some safer cleaning solutions may be effective, but it may take longer to soak. If the cleaner doesn’t work, the acid solution can be used.

Why does my salt cell say inspect cell?

The “Inspect Cell” indicator illuminates when a manual reset is required for the salt generator. This is due to the fact that each cell has a maximum operational lifespan of 500 hours and must be reset upon reaching this limit. To initiate the diagnostic mode, press and hold the “Diagnostic” button for a period of between three and five seconds.

How to clear the check system on Hayward?

In order to reset an Inspect Cell alarm, it is necessary to press the “Menu” button, navigate to the “Default Menu” screen, and then press the “+” key.

How do I reset my Aquarite salt chlorinator?

To reset a T-Cell-15’s salt level, follow these steps:

1. Test the water with salt water test strips to determine the correct salt level.
2. Move the main switch from “Auto” to “Off” and then back to “Auto” with the pump running.
3. Push the Diagnostics button 5 times after hearing the click.
4. If the salt level is 3100, reset it to 4400.
5. Check the age of the cell and try cleaning it if it is a few months old or longer.
6. In the diagnostic menu, check the amps and volts readings.

InyoPools Product Specialist Matt S. can provide more information on how to reset a T-Cell-15’s salt level.