The Magic Heat Reclaimer is a waste heat circulator that can be used to clean and reuse waste oil burning stoves. It is essential to follow the precautions on the ammonia container label and ensure proper ventilation when using it. To clean the reclaimer, place ammonia in a well-ventilated area and cover the outlet for one to two hours. This should work the creosote loose and make it easier to scrub away.
During a power outage, remove the back panel from the Magic Heat within 15 to 20 minutes to allow heat to escape the device, ensuring proper electrical components and heat transfer. The knob in the center of the front should be moved at least once a day. To convert liquid water into steam, the reclaimer must be heated into steam, similar to a tea kettle on a stove.
To clean the reclaimer, use the Soot Scraper knob to scrape soot off the heat exchanger tubes several times during daily cleaning. A better Magic Heat model has a built-in cleaning mechanism that can be accessed once a week or so, but it is not recommended.
Heat reclaimers are dangerous as they sap out heat from the exhaust, causing a large increase in creosote formation. One user took apart a Magic Heat reclaimer to clean, but a bare-ended white wire came off and was difficult to locate where it reattached.
📹 Wood Stove Magic Heat Re-claimer Exchange – Clean Re-Built for My Waste Oil Burning Stove
Wood Stove Magic Heat Re-claimer Exchange – Clean Re-Built for My Waste Oil Burning Stove My Channel Disclaimer: These …
Why are heat reclaimers bad?
Magic Heat is a device that can be dangerous during a power outage due to the distribution fan’s role in pushing heat out of transfer tubes. If power is lost, the fan can deteriorate electrical components and heat transfer tubes may glow red-hot. To prevent this, it is essential to remove the back panel within 15 to 20 minutes during a power outage. Magic Heat is limited to coal or wood-burning appliances with 6″ or 8″ chimneys, as demand for gas-powered heaters has decreased over time.
How do you clean a heat machine?
The text proposes the use of a towel for the removal of residue from the smooth surface, indicating that this method is both straightforward and efficacious for the cleansing process.
How to clean a baffle?
Baffle filters are essential components of a kitchen’s ventilation and exhaust system, typically made from 430 stainless steel, aluminum, or mild steel. They are located in the visible part of a canopy hood, facing down to the cooking equipment. They force grease-saturated air to change direction quickly and repeatedly as it rises through the filter. Grease droplets condense on the metal blades and drain into the filter, preventing buildup that can hinder airflow and filter functioning over time.
Baffle filters are used to block flames from spreading, ensure even air flow throughout the hood canopy, and are low maintenance compared to other filters. They are dishwasher safe and made of durable stainless steel, making them a low-maintenance option. After the washing cycle, check the filter to ensure all grease residual is completely removed.
Can you clean wood burners with WD40?
WD-40 is a highly effective cleaning solution for wood burner glass due to its ability to dissolve tough soot and creosote deposits and break down residues quickly. It is more affordable and widely available, making it a cost-effective solution for cleaning stove glass. However, specialized glass cleaners like Rutland Stove Glass Cleaner and Stove Bright Glass Cleaner are more potent but can be harsher on the glass and surrounding materials.
Commercial cleaners, on the other hand, are more expensive and designed for a specific task, making them less valuable. They are also more flammable, so it is essential to ensure the stove has cooled down before using WD-40. Commercial cleaners, on the other hand, are non-flammable and designed for wood burner glass cleaning, making them safer for day-to-day use, especially for those not used to being very careful.
In conclusion, WD-40 is a more cost-effective and versatile solution for cleaning stove glass, but it is important to ensure the stove is cooled down and the product has fully evaporated before using it again.
Can you use WD-40 to clean stove burner?
Electric stove owners often face hard-to-clean stains on their stove’s glass top, which can be unsightly and potentially pose a health hazard. To remove these blemishes quickly and thoroughly, apply WD-40 to the affected burner to loosen hardened stains and wipe them off easily. WD-40 is a versatile household staple that can be used to clean both inside and outside the home, but controversy lingers over its use in areas close to food contact. Cleaning professionals typically prefer safer formulas like dishwashing liquid, white vinegar and baking soda, and products specifically designed to tackle stovetop grime.
However, WD-40 can be used safely if applied carefully and wiped with soapy water afterward. WD-40’s Specialist Cleaner and Degreaser is a non-flammable and non-abrasive solution that can break up grease while being safe on glass, stainless steel, granite, and other common household materials.
To clean the stove top, turn it off and cool completely before cleaning, as doing so while the appliance is still on and heated could crack the glass. Use a can of WD-40, a soft sponge or microfiber cloth, and an additional rag for drying after removing the stain.
How do you clean an inner burner?
To clean electric stove burners, soak the burner heads and caps in soap and warm water for 30 minutes. Fill a spray bottle with half water and half distilled white vinegar, let it sit for 20 minutes, and mix baking soda and water to create a paste. Use a non-abrasive scrubber and paste to scrub burner parts, and use a paperclip to clear clogged port openings.
To clean electric stove burners, follow the same cleaning supplies as gas stove burners. If the burners have caked-on grime, turn them on for a few minutes to burn off residue. After cooling, gently pull the burners out from the connector, wipe off the prongs and inside of the receptacle with paper towels, and reconnect the burner.
How do you clean the inside of a burner?
To remove stubborn stains from stove burner heads and caps, create a paste of half baking soda and half water. Apply the paste to surfaces and scrub with a non-abrasive pad and toothbrush. Avoid using toothpicks or bleach for porthole cleaning. Rinse and dry parts thoroughly under running water, shaking them to remove excess water. Allow parts to air-dry completely before reassembling the burners.
How long do baffle plates last?
The baffle plate is a crucial part of a firebox, retaining heat and pushing it out of the room. It should last between five to eight years and is designed to be replaced as they take the main heat in the firebox. To replace a baffle plate, lift it up on an angle and drop it down on top of the hangers, which are positioned either side of the roof of the firebox. This process is simple and ensures the firebox remains functional and safe for use.
Do you need to clean a baffle plate?
The baffle plate, a crucial component of stoves, is considered a “consumable” part due to its exposure to intense heat and potential abuse by over-firing. Stove manufacturers generally provide limited warranty coverage for this component, making it essential to regularly clean and inspect it for signs of wear and tear. This is particularly important for multi-fuel boiler stoves, which produce more soot due to lower flue gas temperatures and soot-producing fuels like coal.
Clearing away soot debris helps maintain efficient stove and flue draught, reducing the risk of smoke or carbon monoxide entering the room. Soot build-up on the baffle plate can also re-combust and start fires at the stove’s top or base. Debris left for extended periods can attract condensation and “cake” moisture, rusting the metal baffle plate and stove bodywork. To prevent this, it is recommended to remove caked soot before it cakes, making wire-brushing easier.
Is WD-40 safe on wood?
WD-40 Multi-Use Product is a versatile solution for restoring the luster of wooden furniture and other items. It involves cleaning the surface, applying a small amount of the Original WD-40 Formula, and gently rubbing it onto the wood. The oil in WD-40 helps condition the wood, enhancing its natural shine and color. This technique can revitalize old wooden chairs, tables, picture frames, and other wooden objects.
When repurposing used or second-hand items, adhesive residue from stickers or labels can be dissolving. Spraying the formula onto the sticky residue and letting it sit for a few minutes can help remove it effortlessly.
WD-40 Specialist® Penetrant is particularly useful for breaking the bonds of rust deep inside parts or hardware. Its light lubricant allows for easy manipulation of stuck parts, allowing for the salvage of old motors, vintage toys, or other mechanical items.
📹 Magic Heat, Magic Heat Reclaimer “DISAPPOINTMENT”!!!!!!!!!!!!!!!!!
Further Experience: I happened into one of these heat reclaimers and a pre-catylitic-combustor Blaze King stove for $200 on a sweltering afternoon. I poked at the char built up on the exchanger tubes and began to recognize that this device functions as a smoke condenser. Mine has a tag riveted to the back saying to disassemble and clean the device annually. The idea of disassembling it to scrape off the charred condensate every year suggests to me that the thermostat ought not be any colder than the original. After heating with wood for almost 40 years, I think it generally true that wood stoves need to be run hot rather than allowed to smolder, a conclusion that dawned after a five-second-long chimney fire. It sounded like a jet engine and, fortunately, went right out when I closed the damper. Unattended, the burning creosote might have burnt out the single-wall pipe and burnt down the building. My search shows a similar (identical?) new one retailing for $219 but then again, this is a bulky, heavy, easily-dented item and would cost at least $100 to ship anywhere. If I had one and no use for it, I’d clean it like this one is and put it on Craigslist “asking $175”.
yes did you put the close off baffle back in pipe some place – i think that would slow the exhaust flow -an help the heat reclaimer work better/close the damper a little at a time an find the sweet spot/watching temperature on piping-an done let your wood stove burn too fast/dose your stove have the secondary burn-epa rating/also seal all joints with stove sealant in a calking -at lowes/put the damper after the reclaimer/12 or more inches-this is my advice only /a epa wood stove burns less wood too/thanks much
Creosote is acidic, I think that’s why your pipes had holes in them. I would burn really hot fires every weekend to clean that stuff out, hot fires burn up creosote. Sorry you had to go through that fan blade ordeal, I hope you got something back that made up for it. People pick on guys like me that hoard stuff, but hey, you just found out why it’s a good idea. 🙂
I have some articles on YouTube about the Consolidated Dutchwest wood stove and the Magic Heat if you’re interested. I’ve had my Magic Heat for probably 50 years probably. My MH was used on an oil stove in a garage and then on a gas fired furnace in the basement of my 100 year old house and boy did that make a difference!!!!!!!. I brought it with me to my new house and installed it on my wood stove and its been great all these years. Alas I had to remove it this year because something happened to the pipe scraper. Its not creosote buildup that’s causing the problem, but rather the plate cocks on the rod and binds up and there is no way I can get in there to fix it. Now I’m running my stove with just the blower and a one of those passive fans like you have. I may buy a new one, but I just wanted to mention that my old MH had 14 tubes instead of just 10. You have a catalytic stove there. When’s the last time you checked the catalytic combustor? It seems like the stove may have been overfired a number of times to cause that much damage to the Magic Heat and the pipes. I never seen that happen before. Nice article!