The Sta-Rite modular media filter system is designed to filter water for swimming pools and spas. To install the filter, pour new pool silica sand into the tank and position one corner of a bag of pool-grade silica filter sand over the mouth of the tank. Make a small cut in the corner of the bag to allow sand to slowly fall into the tank. Work slowly and carefully to prevent any sand from spilling. Repeat until the amount of sand needed for your filter is added.
The Sta-Rite modular media filter system brings the proven performance of Sta-Rite’s sophisticated sand filter hydraulics in the easiest to operate filter. It is highly efficient and yields a uniform flow pattern. Modular filter tanks allow for quick change of filter medias without changing the tank. The filter module should normally be cleaned when the filter is installed.
To change sand in a pool filter, pool maintenance, and servicing pool filters, follow these steps:
Pour new pool silica sand into the tank. Position one corner of a bag of pool-grade silica filter sand over the mouth of the tank. Make a small cut in the corner of the bag to allow sand to slowly fall into the tank. Work slowly and carefully to prevent any sand from spilling.
Set the valve on top of the filter to the “Backwash” position. The flow of water is automatically reversed through the filter so that the flow of water is reversed.
In summary, the Sta-Rite modular media filter system is designed to filter water for swimming pools and spas, and its installation requires careful attention to prevent unnecessary service calls and injuries.
📹 POOL SAND FILTERS 101: Easy Operating Guide for Beginners | Swim University
Sand filters are relatively easy to use and maintain. But only if you know how each setting works and how the water flows through …
Can you put too much sand in a pool sand filter?
To improve the effectiveness of your filter tank’s backwash and rinse cycles, it’s essential to have enough sand in the tank. When changing sand, backwash it to eliminate fine sand that may cycle through the filter and end up at the pool’s bottom. Set the filter to “RINSE” to pack new sand down and reduce loose sand. Turn off the pump before switching valve settings to avoid damaging the spider gasket. For filter and multiport valve replacement parts, visit these sources.
How much sand goes in a Sta Rite pool filter?
The sand filter manufacturer requires Pentair – Pac Fab – Sta-Rite products, specifically the TA35100, TA40175, TA50225, and TA60325 models, in pound quantities.
Is 20 PSI too high for a pool filter?
Filter pressure can increase due to dirty filters or other issues. If the pressure is 10 or more PSI above the ideal, it’s time to clean the filter. Remove the cartridge or backwash a DE or sand filter. If the pressure returns to the ideal, the filter is clean. If the pressure gauge still reads high, it may indicate issues with the pool pump, filter medium, broken parts, or lime deposits in the heater. Check for closed, partially closed, or blocked returns or return valves, as well as any issues with the filter medium or filter medium.
How often should I backwash a sand filter?
A sand pool filter uses 20-grade sand to trap particles in pool water, capturing 20-100 micron range particles. As the filter collects more particles, it becomes less efficient, collecting dirt. Backwashing is necessary when the pressure gauge reads 8-10 pounds higher than when the sand was new and clean. There are three main types of pool filters: sand filters, DE filters, and cartridge filters. Sand filters last longer and are easiest to maintain, with a cleaning frequency of about 5 years.
DE filters require cleaning at least once annually, and cartridge filters do not require backwashing but are cleaned with a hose. The sand in a sand filter should be replaced about every seven years due to gradual deterioration. Symptoms include backwashing more often, dirtier pool water, increased chemical usage, or frequent pump operation. The sand should be replaced if the filter needs to be replaced due to the gradual deterioration of the sand.
How many times do you backwash a sand filter?
To maintain a clean pool, it is recommended to backwash your pool once a week or in conjunction with scheduled maintenance. The industry standard is to backwash when the filter’s pressure gauge reads 8-10 PSI over the starting level. Backwashing should also be considered after major storms or algae outbreaks, and after the foliage has dropped. If you have a diatomaceous earth (DE) filter system, it should be cleaned at least six times per year, while a sand filter should be cleaned twice a year and backwashed monthly.
What setting should the sand filter be on?
The filter setting on the multiport valve is of paramount importance in the context of pool filtration, as it facilitates the transfer of water through the filter media, thereby enabling the trapping of dirt and debris prior to their return to the pool. Furthermore, this setting is utilized for the purpose of vacuuming the pool. When the filter is set to “Backwash,” the flow is reversed, flushing out any accumulated dirt and debris in the filter medium and directing it to the waste outlet.
What should psi be on STA Rite pool filter?
Understanding your pool filter’s pressure gauge is crucial. The normal range for pool owners is around 10 PSI, as per the owner’s manual. It’s essential to check the pressure gauge once a week as part of your pool maintenance routine. As long as the water pressure is within this range, your pool filter is in good working condition. However, each pool filter system operates differently, so consult your manufacturer or a pool professional to determine the “normal” range for your model.
How many hours a day should I run my sand filter?
Water circulation is crucial for a healthy swimming pool, preventing cloudy water and algae. To maintain cleanliness, keep your pump and filter system running for 8 to 12 hours, and monitor your water level. Deep clean your pool filters or sand twice a year to ensure smooth operation. To save money, run your pool pump during the night, as local energy companies may charge more during peak hours. If you want your pump to run during the day, schedule it during the hours most people are at work or away from home, such as 9 am to 5 pm. This will help ensure your pool is safe and clean.
Should pool sand filter run all the time?
The pool filter should be run at least 12 hours a day during the summer to clean out dirt, grime, and debris from swimmers. During winter months, it’s not necessary to run the filter as often, but if possible, try to run it for at least eight hours a day. The best time to run the filter is when the water is warmest or the temperature is hottest, with a good time for summer running from 7 am to 7 pm.
Runting your pool pump also matters, as it helps maintain its good condition and prevents algae growth and debris buildup in the pool. Most pool filters have automation settings or timers that can be set to start and shut off at specific times. It’s essential to run the pump when the water is warmest or the temperature is hottest, as this helps prevent freezing and maintain the pool’s appearance.
How do I know if my sand filter is working properly?
The sand filter in your pool should be functioning properly by checking the pressure gauge, which should be between 10 and 25 PSI. If the pressure is higher than usual, it needs cleaning through backwashing. If it’s lower, it’s likely due to blockages in the filter, such as leaves or debris blocking the skimmers, drain covers, pump basket, or impeller. Additionally, checking the water can help determine if the filter is working properly. If there’s a buildup of dirt and debris in the pool, it’s likely that the filter needs attention.
📹 How to correctly Instal a Sand Filter adding the Sand and setting the Laterals. Swimming pool craft
I show you how to not break your pool filter before you even get to turn it on. The most important part is positioning the laterals and …
Here’s the sand filter settings and operation covered in the article 👍 And if you want more help, grab the Pool Care cheat sheet at swimuniversity.com/cheatsheet 00:56 – Sand Filter Settings 01:26 – #1. Filter Setting 01:40 – #2. Backwash Setting 02:39 – #3. Rinse Setting 02:59 – #4. Waste Setting 03:28 – #5. Recirculate Setting 03:45 – #6. Winter/Closed Setting 04:02 – Filter Pressure Gauge 04:45 – Air Relief Valve 05:21 – How Often Should You Clean or Change Filter Sand?
Boy, do I feel like a schmuck. For the last 6 months (since getting our pool), we’ve had the filtration system on “recirculate” (as per our contractor who told us to do that). I didn’t know that the recirculated water wasn’t hitting the sand filter until I watched this article. That explains why the pool was so cloudy all the time!! Thanks for your helpful article.
Thanks for the graphical and clear explanations of the different modes – useful. I’ve installed (replacement) a brand new sand filter unit on my above ground pool. All seemed fined but ~1 week later when I run a backwash, there’s an obvious amount of sand coming out (seen through the glass and waste water) during the backwashing. When I run RINSE, either no sand or just couple of grains may appear in the glass. So far, no obvious sand being sent back in the pool. Do I have an issue? Or does the sand just need to settle in more in the tank? Trying to figure out if it is normal, or if something is broken inside, or if I messed up the install (re-reading the instructions, I did not put water in the tank before putting the sand in.). Or am I missing a seal or something. Ideas?
Hello! Thank you so much for your articles. You helped us open our pool tor the first time last year and here we are again! I do have a question about the system. When we shut off the filter after running it for a bit – the water in the skimmer seemed to kick back and allowed the debris to fall into the pool water and the basket by the motor seemed like it wanted to burst out of the container. Is this something you’ve dealt with before? Any recommendations?
How often does sand need to be added to a sand filter? I’m pretty sure the installers said to add a bag every year but a friend said he’s never added any. I don’t think I lose much over the course of the summer backwashing every week. I’ve had it two summers and just checked it but not sure how full it should be. Thanks in advance and I love your articles and tutorials!
Thanks for this, nice to know what all those settings are! The difference between backwashing and rinsing was not clear to me. I’m new to pool maintenance and I get a lot of conflicting info. Guys doing maintenance here tell me the sand filter needs replacement after 20 years, and they never mentioned anything about adding sand. I’m confused. How do I know when my filter needs more sand?
Would be great to see how the valves need to be set too as I always confuse this On especially how it all needs to be for hoovering And for when I put the pump on for xxx hours to keep it clean or when I leave it overnight after adding chemicals I m struggling now to get my water clear I d love some help We can’t really afford to pay someone to come do it and we forgot to put pump on and add enough chemicals due to a loss in. The family so now I m struggling
I think our filter sand either needs to be cleaned or changed but not sure. We’ve had our home for three years and the previous owners said the sand filter was new. We have a new pump. Our chemicals are fine but our water is still cloudy. We’ve never cleaned or changed the sand in three years. Our pool guy who helps us open the pool said we didn’t need to change the sand but nothing is clearing the water.
I wish you wouldn’t have lumped closed and winter together. We are above the freeze line and have had a lot of frozen valves due to using close instead of winter. Closed does just that it closes the valve trapping water in the valve that can freeze. Winter does just the opposite it completely opens the valve so all water can drain out. You may cost a lot of people a Ruther expensive repair due to a simple oversight.
A great tutorial for beginners. It’s just a pity to have a sand filter in the first place. They are the worst option for pool filtration. Sure they are the world’s most popular filter, but not the best, or the cheapest. They work well for lazy people, who don’t care about the environment, wasted water and chemicals, least effective filter of all. What’s to like?
Putting in the water is a really good tip for newer filters. Back in the day though, those old Baker Hydro filters the laterals were so darn strong I tried stomping on them and my foot lost that fight! This was removing the old filter and putting in a new one. Shame the labels on the multiports don’t even last 3 years now without disintegrating from the sunlight, the old ones used to be some sort of metal that lasted 20 years.
Today I made a huge mistake and agreed to take a look at my friend’s pool filter, I’m a commercial driver by profession, not a pool magician. By the grace of god and the Rock Star article that you posted, an expensive and embarrassing blunder was avoided. Thank you sincerely my friend. I’m clearly no expert, I found a Trojan unlubricated condom worked handily to prevent the sand from going down the feeder tube if you might be clumsy like myself.